Essential Plumber Tips for Installing a Bathtub
Essential Plumber Tips for Installing a Bathtub
Blog Article
We have stumbled on this great article involving Tools You Need to Install a New Bathtub below on the net and accepted it made good sense to write about it with you on this site.
Setting up a tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently available, the job can move rapidly; if you have to open up a wall surface to eliminate the old bathtub and also place the new bath tub, the task is a lot harder. In either instance, the job is within a home handyman's skills, although you will require a helper to vacate the old bathtub and set in the brand-new one. Ensure you have actually qualified yourself for the task as well as fit attempting it. Instead of working with a specialist to take over a halfway-completed job, it is far better to consider employing one before you begin. Chances are you might need a professional plumber to make tube links.
This short article will certainly aid you mount a brand-new bathtub in your bathroom if you have currently acquired a new tub as well as do not need to alter the arrangement of your previous water pipes.
Your tools and product checklist ought to consist of the following:
Preparing for the Setup
First of all, the supporting structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent strain on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly bothersome due to the limited accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bathtub up until the spirit level checks out level.
To set up faucets, fit the bottom of the furthest flexible tap port to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
Activate the water supply and also inspect all joints and new pipework for leakages and tighten them if necessary. Fill up the bathtub as well as likewise examine the overflow outlet and the typical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the supplier's user's manual. Tiling as well as sealing around the bath tub should wait up until the bathtub has been utilized at the very least when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the faucet and also the sink. Protect the tap in place with the manufacturer provided backnut. Once the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap adapters. The former kind should be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a stiff seal, causing the water to permeate the wall surface between the bath and also the tiling, causing issues with dampness as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water prior to sealing, to enable the movement experienced when the bathtub is in use. The sealant can crack relatively very early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very interested in Tools You Need to Install a New Bathtub and I am hoping you enjoyed reading our blog entry. Feel free to take a moment to distribute this article if you liked it. Thanks a lot for your time. Please pay a visit to our blog back soon.
Ensure leak-free homes. Report this page